燃油油面警報
fuel level tell-tale
擋風玻璃電加熱器信號燈
windscreen eletric heater tell-tale
駐車制動系警報燈
parking braking sytem warning tell-tale
被動式乘員安全警報燈
passive restraint tell-tale
乘客與駕駛員聯系信號燈
passenger-driver communication tell-tale
無線電話信號燈
radio communication sytem tell-tale
空氣濾清器警報燈
air filter tell-tale
機油濾清器警報燈
oil filter tell-tale
駕駛室鎖止警告燈
cab lock tell-tale
燈光和照明系統
light and lighting sytem
通用術語
general terms
照明
lighting
燈光
light
光源
light source
燈具的幾何可見度角
angles of geometric visibility of a lamp
外表面
apparent surface
基準軸線
reference axis
基準中心
reference center
發光面
light-emitting surface
照明裝置的光照面
illuminating sruface of a lighting device
反射鏡的光照面
illuminating surface of a reflex reflextor
信號裝置的光照面
illuminating surface of a signalling device
燈組的調整
adjustment of setting
對中
alignment
光色特性
colorimetric characteristics
光度特性
photometric characteristics
光束亮度
beam intensity

光束中心
beam center
遠光束
main beam
近光束
dipped beam
遠光
high beam
近光
lower eam
對稱光
symmetrical beam
非對稱光
asymmetrical beam
眩目
dazzle
眩光
glare
認視距離
bright viewing distance
配光
luminous intensity distribution
透光直徑
transmission diameter
燈光顏色
lamp colr
蘭色
blue
紅色
red
局部黃色
selective yellow
綠色
green
琥珀色
amber
紫色
purple
譜值
spectral value
CIE光色三角區
zone of te CIE color triangle
斷路
break
阻抗
impedance
短路
short circuit
瓦數
wattage
“切斷”電路
"off"circuit
線路圖
wiring diagram
電壓波紋
ripple voltage
起動電流
inrush currant
絕緣強度
dielectric strength
閃頻
flash rate
瞬間超電壓強度
transient overvoltage strength
通電時間
current"on"time
直流電
direct current
交流電
alternating current
會車光束傾斜角
dipped beam inclinatin
燈光明暗截止線
"cut-off"line
初始傾斜角
initial inclination
封閉式燈光組
sealed beam unit
半封閉式燈光組
semi-sealed beam unit
配光鏡
lens(glass lens)
反射鏡`
reflector
配光屏
filament shield
定焦盤
prefocus plate
等照度曲線
isolux curve
等光強曲線
isocandela curve
信號系統
signal sytem
閃光頻率
flash rate
起動時間
starting tiem
光度儀器
photometric device
光學設備
optical device
校準器
aimer
光束軸
beam axle
校準屏幕
aiming screen
聚光裝置
optical block
對光裝置
alignment device
投影設備
projection equipment
遠距離屏幕
distant screen
照明系統
lighting system
照明設備
lightig equipmetn
燈具
lamp
等效燈具
equivalent lamps
成對燈具
lamps constituting a pair
偶數燈
even number of lamps
操作指示燈
operational tell-tale
倒車燈
backup(reversing)lamp
車寬示廓燈
clearance lamp
復合燈
combined lamps
內藏?zé)簦ò禑簦?/span>
concealable lamp
反射發光裝置
reflex reflexting device
回射裝置
retro0reflecting device
放電燈
discharge lamp
霧燈
fog lamp
組合燈
grouped lamps
危險警告燈
hazard warning lamp
近光前照燈
lower-beam (dipped beam)headlamp
遠光前照燈
upper-beam(main beam headlamp)
前照燈水平調整裝置
headlamp levelling device
識別燈
identification lamp
外形示廓燈
end outline marker lamp
牌照燈
license plate lamp
后牌照燈
rear registration plate lamp
可伸縮燈
retractable lamp
封閉式燈
sealed -beam lamp
搜索燈
search lamp
側示廓燈
side marker lamp
單燈
single lamp
專用警告燈
special warning lamp
制動燈
stop lamp
工作燈
working lamp
混合燈
reciprocally incorporated lamp
停車燈
parking lamp
示廓燈
position lamp
轉向信號燈
trun signal lamp
前照燈
headlamp
封閉式前照燈
sealed beam headlamp
半封閉式前照燈
semi-sealed beam headlamp
外裝式前照燈
external mounted headlamp
內裝式前照燈
flush mounted headlamp
輔助前照燈
auxiliary headlamp
組合前燈
comination headlamp
信號燈
signal lamp(indicator)
尾燈
tail lamp
組合尾燈
combination tail lamp
示寬燈
width lamp
示高燈
height lamp
警告燈
emergency warning lamp
門燈
door lock warning lamp
轉向指示燈
turn light indicator(direction indicator lamp)
反射器
reflex reflector
“回路接通”指示燈
"circuit closed" tell-tale
信號燈
pilot lamp
壁燈
bracket lamp
頂燈
ceiling lamp
閱讀燈
reading lamp
踏步燈
step lamp (courtesy light)
儀表板照明燈
instrument panel lamp
攜帶式手提燈
portable lamp
防空燈
black-out lamp
發動機室照明燈
engine compartment lamp
行李箱照明燈
luggage boot lamp
前照燈清潔器
headlamp cleaner
放電燈泡
discharge bulb
白熾燈泡
filament bulb
白熾燈
filament lamp
斜度計
inclinometer
燈泡接頭
bulb adaptor
管狀燈泡
tubular bulb
小型燈泡
miniature bulb
鹵素?zé)襞?/span>
halogen bulb
石英碘燈泡
quartz iodine bulb
閃光器
flasher
電容式閃光器
capacitor type flasher
熱絲式閃光器
hot wire type flasher
翼片式閃光器
vane type flasher
晶體管閃光器
transistor flasher
危險報警閃光器
hazard warning signal flasher
卡口插座
bayonet socket
燈絲
filament
燈泡接電觸點
bulb contact
燈泡燈座片
bulb socket tag
燈泡燈座
contact holder
燈座
lamp seat
調光座盤
beam adjusting disc plate
燈圈
lamp ring
裝飾圈
ornament
燈殼
lamp housing
遮光罩
light shield
分流器
shunt
光電管
photelectric cell
高級轎車車身
limousine body
四門轎車車身
sedan body,saloon body
二門轎車車身
coupe body
活頂轎車車身
cabriolet body
硬頂轎車車身
hardtop body
活頂跑車車身
roadster body, sports car body
四門活頂旅游車車身
phaeton body
活動硬頂轎車車身
hardtop -cabriolet body
旅行轎車或客貨兩用轎車車身
station wagon body, estate car body
小型貨車車身
pick-up body
家庭用旅行車車身
family wagon body
整體車身
unit body (unitized body)
封閉式車身
enclosed body
折背式車身
notch back body
直背式車身
fast back body
半直背式車身
semi-fast back body
艙背式車身
hatch bock body
短背式車身
cut-off type body
方背式車身
square back body
鴨尾式車身
duck tail body
魚雷形車身
torpedo body
結構
structure
楔形造型
wedge style
車身外殼
body shell
空間薄壁結構
space thin0walled construction
車身骨架
body frame
副車架
subframe
邊框式車架
perimeter frame
平臺式車架
platform frame
尾部降低式車架
step-down frame
車身蒙皮
skin
車身結構件
body structural member
承載式車身
unitary construction body (panel structure body,
unitized body, integral body)
非承載式車身
body chassis frame construction (separate frame
construction )
半承載式車身
semi-integral body
骨架式車身
sleleton-type body
半骨架式車身
half-skeleton-type body
無骨架式車身
skeletonless body
車身機構
mechanical hardware of body
折疊式車頂
drop head
天窗車頂
sunshine roof
駕駛區
driver's compartment
乘客區
passenger zone
工具箱
tool box
蓄電池箱
battery comaprtment
行李架
luggage rack
行李架入口高
rack entrance height
行李梯
luggage ladder
座椅
seat
單人座椅
individual seat
雙人座椅
double seat(dual seat)
長座椅
bench seat
高靠背座椅
high back seat
U型座位
U-arranged seat
座椅高
seat height
座墊
seat cushion
座墊靜變形量
amount of static cushion deformation
座墊至頂蓋高
height from seat to roof
靠背
backrest
肘靠
seat armrest
車身裙部
body skirt
輪口
wheel-arch
開縫線
opening line
通道
gangway(aisle)
通道寬
gangway width
內飾
interior trimming
外飾
exterior trimming
車身附件
body accessories
浮筒式
pontoon type
腳部空間
foot well
板件
panel
蒙皮
outer panel skin(skin)
護板
fender (shield)
擋板
baffle(guard)
連接板
connecting panel
導流板
flowguide(air deflector)
襯板
patch
加強件
reinforcement (stiffenner)
固定件
stay (retainer)
支承件
brace
裝飾件
trimming (garnish)
密封件
weather strip(sealing)
支架
support(bracket)
襯墊
pad (packing)
扶手
assist grip(hnadrail)
扶手空間
handrail space
鉸鏈
hinge
立柱
pillar
梁
rail(beam)
罩
housing
蓋
lid(cap)
槽
guide(groove)
前圍
FRONT WALL
前圍骨架
front wall frame
前圍立柱
front wall pillar
前圍擱梁
front wall shelf beam
前圍裙邊梁
front skirt rail
前圍蒙皮
front wall outer panel
前圍護板（欄）
front wall inner shield
前面罩
radiator grille
風窗框架
windshield frame
風窗中立柱
windshield central post
風窗框上橫梁
windshield header crossbar
風窗框下橫梁
windshield cross sill
風窗玻璃
windscreen (windshield)
三角窗
quarter window
儀表板
instrument panel(dash board)
副儀表板
auxiliary fascia console
儀表板護面
dash board facing
氣囊
air bag
保險杠
bumper
刮水器
wiper
風窗洗滌器
washer
后視鏡
rear view mirror
電子后視鏡
electronic mirror
防眩后視鏡
glare-proof mirror
遮陽板（簾）
sun visor
煙灰盒
ash try(ash pan)
點煙器
cigar lighter
除霜器
defroster
防霧裝置
demister
發動機罩
engine hood
后圍
back wall
后圍骨架
rear wall frame
后圍立柱
rear wall pillar
后圍擱梁
rear wall shelf rail
后圍裙邊梁
rear skirt rail
后圍蒙皮
rear wall outer panel
后圍護板
rear wall inner shield
后窗框架
rear window frame
后窗中立柱
rear window central pillar
后窗框上橫梁
rear window header crossbar
后窗框下橫梁
rear window cross sill
后窗玻璃
rear window glass
助力撐桿
power-assisted brace gas spring
側圍
side wall
側圍骨架
side wall frame
側圍立柱
side wall pillar
側窗立柱
side window pillar
腰立柱
waist pillar
門立柱
side wall outer panel
側圍護板
side wall inner shield
側窗
side window
側窗鎖
side window lock
上邊梁
roof side rail(cantrail)
腰梁
waist rail
側圍擱梁
side wall sheilf rail
側圍裙邊梁
side skirt rail
斜撐
bracing piece
輪罩
wheelhouse(wheel arch)
翼板
wing(fender)
擋泥板
madguard(fender apron)
踏步板
step plate
一級踏步高
first step height
踏步深
step depth
流水槽
roof drip
駕駛員門
driver door
乘客門凈寬
service door clear width
安全門
emergency door
發動機艙門
engine compartment door
行李艙門
luggage compartment door
蓄電池箱門
battery compartment door
售票臺
conductor table
售票員座椅
conductor seat
乘客座椅
passenger seat
導游座椅
guide seat
加座
additional seat9folding seat)
襯靠
armrst
安全帶
seat belt(safety belt)
門鎖
door lock
門內手柄
indide door handle
玻璃升降器
window regulator(window lifter)
壓條
trim strip
壓條封蓋
trim strip cap
頂蓋
roof
頂蓋骨架
roof frame
頂蓋縱梁
roof rai
頂蓋橫梁
roof crossrail
頂蓋蒙皮
roof outer panel
頂蓋護板
roof inner shield
頂窗
sky-light window
地板
floor
地板護面
floor carpet
底架
foundation
空調裝置
air conditiner
暖風裝置
heater
冷氣裝置
cooler
除霜裝置
defroster
通風裝置
ventilator
自動調溫裝置
automatic temperature control
吸入節流閥
suction throttling valve
吸進口
suction side
排放口
discharge side
蒸發器
evaporator
蒸發分離器
vapor seperator
蒸發氣體回收管
vapor return line
標牌
name plate
路牌
guide board
伸縮蓬
telescopic tarpaulin
中間框架
central frame
梭梁
stabilizing beam
蓬桿
tarpaulin rod
駕駛室
cab
平頭駕駛室
forward control cab(cab over engine)
長頭駕駛室
conventional cab
側置駕駛室
offset cab
雙排座駕駛室
crew cab (double cab)
有臥鋪的駕駛室
SLLEPER CAB
翻轉式駕駛室
tilt cab
右側駕駛
right-hand drive
左側駕駛
left-hand drive
角撐件
guesset
筋
rib
雜物箱
glove box
內鎖手柄
inside door knob
汽車商標
emblem (mark)
貨箱
cargo body
廂式貨箱
van body
低臺貨箱
low deck body
高欄板貨箱
high gate cargo body
貨箱底板
cargo floor
梁
sill
縱梁
main sill
縱梁墊木
wood filler block
靠枕
head rest
底板邊梁
floor frame
底板面板
floor board
底板壓條
floor strip
繩鉤
rope hook
貨架
front guard frame
貨架邊柱
guard frame ouside post
貨架橫梁
guard frame rail
貨架上角板
guard frame upper gusset
貨加立柱
guard frame inside post
貨架橫擋
guard frame horizontal cleat
貨架立擋
guard frame vertical clear
邊柱上擋
guard fame upper side stopper
邊柱下角板
guard frame lower gusset plate
前板
header board
包邊
board edge iron
貨箱欄板
gate
欄板上梁
gate top rial
欄板下梁
gate bottom rial
欄板鉸鏈
gate hinge
欄板立柱
support post
邊板
side gate
后板
rear gate
后板側柱
rear gate side post
欄板鏈條
gate chain
護套
sleeve
緩沖墊
cushion rubber
板件
pressing panel
骨架件
member
發動機罩安全拉鉤
hood safety lock
背門
back door
地板通道
floor tunnel
保險杠防撞塊
bumper guard
保險杠托架
bumper stay
腳凳
foot rest
車輪裝飾罩
wheel disc (rim embelisher)
輪轂裝飾罩
hub embelisher
車身設計
body design
車身總布置圖
body layout
車身主模型
master model
車身主圖板
full scale draft
油泥模型
clay model (plasticine model)
全尺寸造型模型
full scale styling representation mock-up
造型
styling
原型車
prototype vehicle
彩色效果圖
color picture
黑板圖
black-board draft
車身制圖
body drawing
車身制表面
body surface development
樣板
template
車身分塊
body division
車身坐標軸線
body coordinate axis
三向坐標測量裝置
three coordinates measuring equipment
非接觸仿形測量
non-contact copying measurement
計算機輔助幾何設計
computer aided geometric design(CAGD)
車身機助設計制造一體化
computer aided design/computer aided manufacture
(CAD/CAM)
計算機輔助工程
computer aided engineering (CAE)
貝齊爾曲線
bezier curve
高光線
high-light line
通用駕駛室系統
versatile cab system
有限元法
finite-element method(FEM)
模態分析法
modal analysis method
車身制造
body manufacturing
車身裝焊流水線
body assembly line
車身主裝配臺
main assembling jig of body
大型裝焊架
large-scale jig
低溶點合金模
low melting point alloy die
經濟模
economic die
臨時沖模
temporary die
拉深
drawing
拉深系數
drawing coefficient
電泳涂漆
elecrophoretic coating
靜電噴漆
electrostatic spray paining
脫式浸涂
slipper dip
全浸涂
full dip
轉動浸涂
rotodip
車身油漆
body paint
車身表面處理
body surface treatment
磷化處理
phosphating
遠紅外線烘干
far-infrared ays drying
白車身
body in white
剝裂試驗
peel test
屈強比
yield limit/strength limit
定制車身
custom-built body
回彈
rebound
沖模的楔形機構
wedged mechanism of die
二氧化碳?xì)怏w保護焊
CO2 gas shield welding
車身試驗
body test
車身壽命（疲勞）試驗
body durability test
車身密封試驗
body sealing test
淋雨試驗
rain test
粉塵試驗
dust test
車身振動試驗
body vibration test
空調試驗
air conditioning test
熱線風速計
hot wire anemometer
車身表面壓力分布試驗
body surface pressure distribution test
風洞試驗
wind tunnel test
整車風洞或全尺寸風洞
full scale wind tunnel
開式風洞
open wind turnnel
閉式風洞
closed wind tunnel
阻塞效應
blockage effect
阻塞面積比
blockage area ratio
表面絲線法
surface tuft method
流線圖
flow pattern
顏料流線
paint streaming
車身材料
body materials
高強度低合金鋼
high strength low alloy steel (HSLA)
鍍鋅鋼板
zinc coating steel plate
密封劑和粘接劑
sealer and adhesive
模壓塑料板材
sheet moulding compound (SMC)
纖維
fiber
填料
filler
聚氨脂泡沫（塑料）
polyurethane foam (urethane foam)
安全玻璃
safety glass
后窗玻璃（后擋玻璃）
backlight(backlite)
防彈玻璃
bullet0resisting glass
復合曲面玻璃
complex-curved glass
單曲面玻璃
cylindrically curved glass(single curved glass)
雙層中空玻璃
bouble glazed unit
電熱安全玻璃
electric heating safety glass
增反射安全玻璃
enhanced reflecting safety glazing material
玻璃-塑料安全材料
glass-plastic glazing material
屏顯風窗玻璃
head-up display windscreen
夾層玻璃
laminated-glass
A類夾層玻璃
laminated-glass A
B類夾層玻璃
laminated-glass B
安全玻璃材料
safety glazing material
側窗玻璃
side window glass
鋼化玻璃
tempered glass
前風窗玻璃（前風擋玻璃）
windscreen
無雨刷玻璃
wipeless windscreen
區域鋼化玻璃
zone-tempered glass
鋼化彩虹
trising from tempering float glass
缺角
broken corner
膠合層氣泡
bubble in the interlayer
爆邊
chip
粗磨邊
rude edge-arrissing
吻合度
curvature tolerance
深彎
deep bending
脫膠
delamination
膠合層變色
discoloration
細磨邊
smoothed edge-arrissing
膠合層雜質
interlayer dirt
節瘤
knot
絨毛
fine hair
疊差
dislocation
模具痕跡
mold mark
劃傷
scratch
淺彎
shallow bending
磨邊殘留
edge-arrissing residue
掛鉤印跡
tong mark
波筋
wave
發霉
weathering
視區
vision area
光學偏移
optical deviation
不平行度
wedge
平行度
parallelism
透光率
light transmittance
副像
secondary image
光學畸變
optical distortion
鋼球沖擊試驗
ball impact test
淬火鋼球
hardened steel ball
支承夾具
supporting fixture
耐磨試驗
abrasion test
磨損儀
abrading instrument
旋轉臺
turntable
中心夾具
centre clamp
砂輪
abrasive wheel
光學系統
optical system
白熾燈
incandescent lamp
焦距
focal length
色差
chromatic aberration
光圈
clear aperture
散射光
scattered light
測定散色光的設備
hazemeter
光頸
light trap
碎片試驗
fragmentation test
光霧
haze
自動沖頭
automatic punch
曲面玻璃
curved glass
人頭模型沖擊試驗
head form impact test
人頭模型重塊
head form weight
夾層
interlayer
光譜靈敏度
spectral sensitivity
光譜發光效率
spectral luminous efficiency
國際照明委員會1931
CIE 1931 standard photometric observer
標準色度觀測者
白晝視覺
photopic vision
光通路
light patch
次生影像分離試驗
secondary image separation test
靶標試驗
target test
瞄準望遠鏡試驗
collimation telescope test
單筒望遠鏡
monocular
氣泡
bulb
聚光鏡
condenser
毛玻璃屏
ground-glass screen
濾色片
color filter
極座標片
polar co-ordinate plate
無色透鏡
achromatic lens
黑點
black spot
幻燈片
slide
光珊
grating
幻燈機
projector
顯示屏
display screen
輝紋技術
stration technique
國際照明委員會標準
CIE standard illuminant A
施照體A
色度施照體
colorimetric illuminant values
反射率
reflectance
正規反射率
regular reflectance
擴散反射率
diffused reflectance
反射儀
reflectrometer
光檢測器
photodetector
外來光
extraneous light
穩壓器
voltage stabilizer
落箭試驗
falling dart test
展開面積
developed area
拱高
height of segment
顏色識別試驗
identification of color test
前風窗玻璃的安裝角
inclination angle of a windscreen
光反射率
luninous reflectance
光透射率
luminous transmittance
給定方向的光畸變
optical distortion in a given direction
拋光面
polished edge
主視區
primary vision area
制品
product
倒圓
round edge arrissing
曲率半徑
radius of curvature
抗磨性試驗
resistance-to-abrasion test
耐烘烤性試驗
resistance-to-bake test
耐化學侵蝕性試驗
resistance-to=fire test
耐燃燒性試驗
resistance-to-fire test
耐熱性試驗
resistance-to-high temperature test
耐濕性試驗
resistance-to-humidity test
抗穿透性試驗
resistance-to-penetration test
耐輻照性試驗
resistance-to-radiation test
耐模擬氣候試驗
resistance-to-simulated weathering test
耐溫度變化性試驗
resistance-to-temperature change test
霰彈袋試驗
shot-bag test
試樣
specimens
結石
stone
應力斑
stress pattern
線道
string
試驗片
test piece
破碎后的能見度試驗
visibility-after -fracture test
翹曲度
warpage
汽車的制造工藝
manufacturing process of automobile
鑄造
casting
汽車的生產過程
production process of automobile
定位
locating
工件的六點定位原理
theory of six-point locating of workpiece
加工精度
accuracy of working
尺寸鏈
dimension chain
鑄造工藝
foundry technique(casting technique)
造型工藝
molding process
結構工藝性
structural machinability
有箱造型
tight-flask molding
無箱造型
flaskless mold
地面造型
floor mold
地坑造型
pit molding
高壓造型
high pressure molding
樹脂砂造型
phenolic and molding
疊箱造型
stack molding
制芯工序
coremaking operation
烘干工序
baking operation
鑄造廠
foundry plant
鑄件
casting
為清理鑄件
undressed casting
為經熱處理鑄件
green casting
薄壁鑄件
light casting
厚壁鑄件
heavy section casting
鑄鋼
cast steel
鑄鋼件
steel casting
裝配
assembly
復型鑄造法
double mould casting(dual type casting)
粉未冶金
powder metallurgy
干砂型
dry sand mold
濕砂型
green sand mold
制型材料
molding material
制型芯材料
core molding material
砂芯涂料
core coating
薄殼砂芯
shell core
吹芯
core blowing
擠芯
core extrusion
離心鑄造
centrifugal casting
手工造型
hand molding (hand moulding)
機器造型
machine molding (machine moulding)
木模造型
wood pattern molding
金屬造型
metal pattern molding
壓力鑄造
pressure casting (die casting)
熔模鑄造
hot investment casting
殼型鑄造
shell mould casting
硬模鑄造
metal mold casting
擠壓鑄造
extrusion casting
低壓鑄造
low-pressure casting
電磁壓鑄
electromagnetic propulsion
失蠟鑄造
dewaxing casting
精密鑄造
precision casting
雙金屬鑄造
bimetal casting
實型鑄造
full-mold casting
濕型鑄造
green sand casting
加壓鑄造
compresson casting
機械化鑄造
machining casting
砂箱
casting box
下箱
drag (lower box)
下砂箱
drg falsk (drag box)
上砂箱
cope box (cope flask)
下壓式造型機
molding machine with down sand frame
上壓式造型機
molding machine with top sand frame
震實造型機
bumping molding machine
烘爐
baking oven
高頻烘干爐
dielectric drying stove
松砂機
aerator(fluffer)
烘芯爐
core stove
高頻烘芯爐
dielectric core oven
落砂機
shakeout device (sand shakout,flask shaker)
制芯機
core-making machine
出芯機
core knock-out machine(core breaker0
射芯機
shoot core machine (core shooter)
殼芯機
shell core machine
無芯高頻感應爐
high frequency coreless induction furnace
無芯工頻感應電爐
main frequency coreless inductio furnace
造型機
molding machine
壓實式造型機
squeeze molding machine
轉臺造型機
turntable molding machine
氣動震實造型機
air jarring moulding machine
有箱造型機
box molding machine
壓鑄機
die casting machine
熱室壓鑄機
hot-chamber die casting machine
慣性落砂機
inertia knock-out grid
澆包
ladle
澆注機
cating machine
沖天爐
cupola (cupola furnace)
水冷沖天爐
water cooled cupola
焦碳爐
coke-fired furnace
退火爐
annealing oven
回火爐
drawing furnace
噴丸機
high pressure blasting machine
拋砂機
sand throwing machine
擺輪式混砂機
speedmuller
自動分箱機
automatic box splitter
自動合箱機
automatic closer
自動殼型機
autoclino
風動工具
air tool
鍛造
forging
無型鍛造
open forging
水壓機鍛造
hydraulic forging
機器鍛造
machine forging
自由鍛造
flat-die forging
多型槽鍛造
multiple impression forging
冷鍛
cold forging
錘鍛（自由鍛）
hammer forging
平鍛
horzontal forging
鐓鍛
upset forging
輥鍛
roll forging
模鍛
die forging
熱模鍛
pressure forging
開式模鍛
open-die forging
精密模鍛
prescision drop forging
擠壓模鍛
no-draft forging
冷拉
cold draw
熱拉
hot draw
冷擠壓
cold extruding
切邊
trim
冷切邊
cold trim
熱切邊
hot trim
沖孔
punching
校正
straightening
板料沖壓
sheet stamping
制坯
blank
鍛造毛坯
forging blank
上模
upper die
下模
bottom die(counter die)
上錘頭
top swage
下錘頭
lower die
汽錘
steam hammer
無砧坐模鍛錘
forging hammer without anvilbed
摩擦錘
jump hammer
落錘
block hammer
水平分模（平鍛機）
horizontal parting
冷鍛模
cold forging die
型鍛模
forging die
精整模
forming die
頂鍛模
joggling die
鍛壓機
forging die
水壓機
water press
平鍛機
horizontal forging machine
汽力鍛壓機
steam power forging press
壓彎機
bending press
模鍛壓力機
drop press
曲軸壓力機
crank press
曲柄壓力機
knuckle-joint press
切邊壓力機
trimming press
切斷壓力機
cutting-out press
精壓機
coining press
輥鍛機
forging roll
鐓鍛機
upsetting forging press
噴丸清理
sand blast cleaning
消除內應力
residual stress relieving
水力清理
hydraulic blasting
酸洗
pickling
超聲波清洗
ultrasonic cleaning
超聲波探傷
ultrasonic inspection
沖壓
stamping
沖壓下料
bar stock cutting by punching
沖壓線
press line
凸模
punch
凸凹模
punch-die
沖孔模
piercing die
修邊模
trimming die
預彎模
die for first-forming
扭彎模
twisting die
扭彎模
twisting die
扭彎成形模
twisting-forming die
壓彎模
bending die
壓彎翻邊模
bending-flanging die
壓扁模
flattening die
壓圓模
circular bending die
壓彎卷圓模
bending-curling die
壓彎壓筋模
bending-beading die
落料模
blanking die
落料壓印模
blanking-coining die
落料切槽模
blanking-slotting die
縮口模
neckling die
翻孔整形模
hole flanging-sizing die
翻邊成形模
flanging forming die
切槽模
slotting die
拉延模
drawing die
下料
stock cutting
開卷
unreel
成形
forming
翻邊
flanging
反向拉伸
reverse-draw
整形
restricking
整徑
trued
切口
cut-off (shear-out)
切邊
trimming
壓扁
flattening
應變
strain
壓痕
impression
拉延
drawing
拉伸
deep drawng
擠壓
extrusion
滾擠
roll-forming
卷邊
curling
折邊
edging
刮邊
scraping
三室清洗機
three-stage cleaning machine
三動壓機
triple-action press
折邊機
edging machine
開卷機
decoiling unit
萬能液壓機
universal hydraulic machine
機械壓力機
mechanical press
氣動壓力機
pneumatic press
沖孔機
punch machine
彎曲機
bender
彎管機
pipe bending machine
輥壓機
rolling press
滾式彎板機
roll-type sheet bending machine
板料校平機
sheet flattening machine
退料板
stripper
高速棒料剪切機
high speed cropping machine
剪床
shearing machine
轉塔式?jīng)_床
turret-type punch press
校直機
straightener
擠壓機
extrusion press
滾壓擠壓機
hydraulic extrusion press
卷邊機
folding machine
精壓機
coining press
上料器
loader
落料機
blanker
搓絲機
thread rolling machine
滾剪機
roller shearing machine
焊接
welding
十字接頭
cross-shaped joint
T形接頭
T joint
單J形坡口
single-J groove
單U形坡口
single-U groove
雙V形坡口
double-V groove
K形坡口
double-vevel groove
雙V形對接接頭
double-V butt joint
Y形坡口裂縫試驗
Y-slit crack test
TIG保護焊
tungsten inert gas (TIG) arc welding
TIG點焊
TIG spot welding
立焊
vertical position of welding
火焰釬焊
brazing by flame
氣體保護電弧焊
gas shield arc welding
氣焊
gas welding
氣電焊
electrogas arc welding
水下焊接
underwater welding
水蒸氣保護電弧焊
water vapor arc welding
水平角焊
horizontal fillet welding
手工焊
manual welding
手工電弧焊
covered arc welding
仰焊
face-up bonding
正面角焊縫
front fillet weld
加壓氣焊
gas pressure welding
加壓鑄焊
pressure thermit welding
返修焊
rewelding
向上立焊
vertical up welding
向下立焊
vertical down welding
平焊（俯焊）
flat position welding
點焊
point welding
雙面焊
weld from both sides
雙面點焊
direct welding
雙弧焊
twin arc welding
壓焊
pressure welding
多道焊
multipass welding
多點凸焊
multiple projection welding
多層焊
multilayer welding
定位焊
tack welding
冷壓焊
cold pressure welding
環焊
boxing
自動焊接
automatic welding
自動點焊
stitch welding
自動氣割
automatic gas cutting
無氣體保護電弧焊
non gas shielded arc welding
對接焊
butt welding
補焊
repair welding
深溶焊
deep penetration welding
滾對焊
butt seam welding
滾焊
seam welding
滾點焊
roll spot welding
橫焊
horzontal position welding
橫向焊縫
cross weld
金屬極惰性氣體保護點焊
metal inert gas arc welding
金屬極電弧焊接
metal arc welding
電焊
eletric welding
電子束焊接
electron beam welding
電子加熱釬焊
electric brazing
電阻焊
electric resistance welding
電弧焊
electric arc welding
堆焊
bead welding
坡口焊
groove welding
封底焊道
sealing run
搭接焊
lap welding
激光焊接
laser welding
熱焊
hot weld
單面焊
welding by one side
單面點焊
indirect welding
單道焊
single-pass welding
單層焊
single-layer welding
單邊多點點焊
series spot welding
單邊多電極焊
series welding
仰焊
overhead position welding
熔焊
fusion welding
氬弧焊
argon arc welding
跳焊
skip welding
惰性氣體保護焊
inert-gas welding
埋弧自動焊
unionmelt welding
碳弧焊
carbon arc welding
躺焊
fire-cracker welding
縫焊
seam welding
鍛焊
blacksmith welding
磁性氣體保護焊
gas shielded magnetic flux arc welding
焊接工藝
welding procedure
焊態
as-welded
焊道
bead
焊肉致密
dense deposits
焊后強度
as-deposited strength
焊道裂紋
bead cracking
焊縫
seam
焊根
root of weld
焊波
ripple
焊透
complete penetration
未焊透
incomplete penetration
焊核
nugget
熔滴
droplet
熔敷工藝
deposition techniques
咬邊
undercut
去渣
deslag
焊接缺陷
weld defects
乙炔罐
acetylene cylinder
乙炔發生器
acetylene generator
注水式乙炔發生器
water to carbide generator
投入式乙發生器
carbide to water generator
乙炔氧焊裝置
acetylene-welding installation
點焊鉗
spot welding head
三相整流焊機
three phase rectifier welder
三相低頻焊機
three phase low frequency
萬能滾焊機
universal seam welder
手動焊炬
hand torch
手動焊槍
hand held gun
壓焊機
press welder
交流弧焊機
AC arc welding machine
多點焊機
multiple spot welder
多站電焊機
multi-operator welding set
切割機
cutting machine
氣瓶
gas cylinder
保護罩
protective boot
電子槍
electron gun
電阻對焊
butt resistance welding
電焊機
electric welding
電弧焊機
arc welding machine
電渣焊機
electroslag welding
仿型氧氣切割機
template-type axy-cutting machine
抽頭式焊機
welder with taps
仰焊機
overhead welder
單站弧焊機
single operator welding machine
移動式焊機
portable welding machine
移動式接觸焊機
portable resistance welder
移動式點焊機
portable spot welder
蓄電池式焊機
battery welder
縫焊機
seam welder
大焊絲盤
large spool
焊工用玻璃
welding galss
焊工用護目鏡
welding goggles
焊工用面罩
helmet shield
焊把
holder
乙炔
acetylene
電石
calcium carbide
電極（焊條）
electrode
手涂焊條
dipped electrode
合金焊條
hastelloy electrode
雙芯焊條
twin electrode
雙層藥皮焊條
double coated electrode
機械壓涂焊條
extruded electrode
包絲焊條
flyspun electrode
深熔焊條
deep penetration electrode
鐵粉焊條
iron powder electrode
堆焊焊條
surfacing electrode
碳極
carbon electrode
機加工
machining
車削
turn
高速切削
high speed cutting
強力切削
power cutting
多刀切削
multi-tool cutting
深孔加工
deep hole working
高速精鏜
high speed boringh
高速滾削
high speed hobbing
平面銑削
surface milling
鏜削
boring
拉削
broaching
成型拉削
form broaching
連續拉削
continuous broaching
分層拉削
progressive broaching
推削
push broaching
刨削
shaping (planing)
磨削
grinding
外圓磨削
cylindrical grinding
內圓磨削
internal grinding
端面磨削
cross grinding
周面磨削
peripheral grinding
插削
slotting
鏟削
relieve
鉆削
drill
導電磨削
electrical grinding
無心磨削
centerless grinding
高速磨削
high-speed grinding
強力磨削
power grinding
珩磨
honing
研磨
lapping
超精加工
superfinishing
齒面加工
gear face machining
拉齒
broaching gear
銑齒
gear milling
插齒
gear shaping
滾齒
gear hobbing
刨齒
gear planing
剃齒
gear shaving
研齒
gear lapping
珩齒
gear honing
磨齒
gear grinding
擠齒
gear extruding
普通剃齒法
general shaving
對角剃齒法
diagonal shaving
切向剃齒法
tangential shaving
剃鼓形齒
crown shaving
砂帶磨削
abrasive belt gringding
滾壓光加工
rolling finishing
單面切削法
single-side cutting method
雙面切削法
spread -blade cutting method
展成法切齒
gear-cutting with generating method
仿形法切齒
gear-cutting with form copying method
成型插齒
shear-speed gear cutting
花鍵加工
splining
螺紋銑
thread milling
螺紋磨
thread grinding
鏜孔
boring hole
鉸孔
ream
锪孔
counter sinking
滾絲
thread rolling
套絲
thread chaing
攻絲
thread tapping
旋風切削螺紋
whirl wind cutting thread
少無切削加工
non-chip finish
擠壓光加工
extrusion finishing
精密加工
precision work
超精加工
superfinishing
粗加工
rough machining
化學機械加工
chemical mechanical working
電熱加工
electro-thermic working
陽極機械加工
anode mechanical working
電脈沖加工
electro-spark machining
電火花加工
electro-spark machining
電子束加工
electronic beam machining
電解加工
electrolytic machining
超聲波加工
ultrasonic machining