Abrasive wear        M磨粒磨損
Accuracy of bevel and hypoid gears Z錐齒輪和準雙曲面齒輪 精度
Accuracy of cyllindrical worm and wormwheel Y圓柱蝸桿、蝸輪精度
Accuracy of fine-pitch bevel gears        XMSZ小模數錐齒輪精度
Accuracy of fine-pitch cylindrcal worm and wormwheel XMSY小模數圓柱蝸桿、蝸輪精度
Accuracy of involute cylindrcal gears        J漸開線圓柱齒輪精度
Accuracy of rack        C齒條精度
Active flank        Y有效齒面
Addendum        C齒頂高
Addendum angle        C齒頂角
Addendum coefficient        C齒頂高系數
Addendum modification        J徑向變位(變位)
Addendum modification coefficient        J徑向變位系數(變位系數)
Addendum modification(for external gears ):Dedendum modification (for internal gears ) J徑向變位量(變位量)
Addendum modification of wormwheel        W蝸輪齒廓變位量
Addendum modification on gears C齒輪的變位
Archimiedes spiral        A阿基米得螺線
Addendum        C齒頂高
Addendum flank        S上齒面
Addendum modification coefficient of wormwheel W蝸輪變位系數
Angular dimensions J角參數
Angular pitch C齒距角
Annulus gear N內齒圈
Apex crlssing point and locating face        D頂點，交點和定位面
Apex to crown        G冠頂距
Arc-contact worm, Hollow flank worm, ZC-worm Y圓弧圓柱蝸桿（ZC蝸桿)
Associsted gear failure        Q其它損傷
Axial diametral pitch        Z軸向徑節
Axial dimensions        Z軸向參數
Axial modification,Longitudinal correction        C齒向修形
Axial module Z軸向模數
Axial pitch        Z軸向齒距
Axial plane        Z軸平面
Axial plane of worm        W 蝸桿軸平面
Axial plane of worm        W 蝸輪軸平面
Axial profile        Z軸向齒廓
Axial profile angle of worm W蝸桿軸向齒形角
Axial space width        Z軸向齒槽寬
Axial tooth profile        Z軸向齒廓
Axial tooth thickness        Z軸向齒厚
Back cone        B背錐面（背錐）
Back cone angle        B背錐角
Back cone distance        B背錐距
Back cone tooth profile        B背脊齒廓
Backlash C 側隙
Ball oscillating tooth        G滾珠活齒
Base circle        G基圓
Base circle of involute helicoid worm        J漸開線蝸桿基圓
Base clylinder        J基圓柱面
Base cylinder of involute helicoid worm        J漸開線蝸桿基圓柱面
Base diameter        J基圓直徑
Base diameter of involute helicoid worm J漸開線蝸桿基圓直徑
Base helix        J基圓螺旋線
Base helix angle        J基圓螺旋角
Base lead angle        J基圓導程角
Base lead angle involute helicoid worm        J漸開線蝸桿基圓柱導程角
Base pitch        J基圓齒距
Base pitch of involute helicoid worm J漸開線蝸桿基圓柱齒距
Base tangent length G公法線長度
Basic parameters for cylindrical gear units Y圓柱齒輪減數器基本參數
Basic parameters of cylindrical worm gears Y圓柱蝸桿基本參數
Basic rack        J基本齒條
Basic rack tooth profile of fine-pitch bevel gears X小模數錐齒輪基本齒廓
Basic rack tooth profile of fine-pitch cylindrical worm        X小模數圓柱蝸桿基本齒廓
Basic rack tooth profile of invoiute cylindrical gears        J漸開線圓柱齒輪 基本齒廓
Basic terminology of cycloidal drives        B擺線針輪行星傳動 基本術語
Basic terminology of gears        C齒輪基本術語
Basic terminology of planetary drives X行星傳動基本術語
Basic tooth profile of cylindrical worm        Y圓柱蝸桿基本齒廓
Basic tooth profile of straight and skew bevel gears        Z直齒及斜齒錐齒輪基本齒廓
Basic worm        J基本蝸桿
Bevel and hypoid gears and gear pairs Z錐齒輪 準雙曲面齒輪及其齒輪副
Bevel gear Z錐齒輪
Bevel gear pair Z錐齒輪副
Bevel gear pair with small teeth difference Z錐齒少齒差齒輪副
Bevel gears-information of the dimensional data to be given on the drawing        Z錐齒輪圖樣上應注明的尺寸數據
Blank deficiencies        L輪坯缺陷
Bottom clearance        D頂隙
Bottom clearance coefficient        D頂隙系數
Bottom land ，Bottom of tooth space        C齒槽底面（槽底)
Bottom of tooth space        C齒槽底
Breakage        L輪齒折斷
Calculation of scuffing load capacity for involute cylindrical gears        J漸開線圓柱齒輪膠合承載能力計算方法
Case crushing        B表層壓碎
Centre circle of gear pins(distribution circle)        Z針齒中心圓（分布圓）
Centre circle of gear pins(distribution cylinder)        Z針齒中心圓柱面（分布圓柱面）
Centre circle of pin holes        Z柱鎖孔中心圓
Centre circle pitch of gear pins(distribution circle pitch) Z針齒中心圓齒距（分布圓齒距）
Centre cylinder of pin holes        Z柱銷孔中心圓柱面
distance        Z中心距
Centre distance（eccentricity)        Z中心距（偏心距）
Centre distance of gear pins(distribution diameter) Z針輪中心圓直徑（分布圓直徑）
Centre distance of pin holes        Z柱銷孔中心圓直徑
Centre distance modification coefficient Z中心距變動系數
Centre gear        Z中心輪
Centre surface of pin holes        Z柱銷孔中心曲面
Chordal height        X弦齒高
Chordal tooth tnickness        X弦齒厚
Circle at root of gorge        W蝸輪喉圓
Circles Y圓
Circular-arc gear Y圓弧圓柱齒輪
Circular-arc gear drive with small teeth difference Y圓弧少齒差齒輪傳動
Circular-arc gear pair Y圓弧齒輪副
Circular arc gear pair with small teeth difference Y圓弧少齒差齒輪副
Circular arc spur gear        Y圓弧直齒輪
Circumferferential backlash        Y圓周側隙
Circumferferential restricting mechanism        Z周向限制機構
Cleanliness of gear units        C齒輪傳動裝置清潔度
Clearance and backlash        D頂隙和側隙
Coefficient of facewidth        C齒寬系數
Coefficient of gear pin diameter        Z針輪系數
Cold flow        N碾擊塑變
Common apcx        G公共錐頂
Common normal lengh(cycloidal gear) G公法線長度（擺線輪）
Common normal lengh( pin wheel)        G公法線長度（針輪）
Compound oscillating tooth        Z組合活齒
Compound planetary gear train F復合行星齒輪系
Compound planetary gear train Z組合行星齒輪系
Cone angle        Y圓錐角
Cone distance        Z錐距
Conical spiral        Y圓錐螺旋線
Conjugate profile F復合行星齒輪系(復合行星齒輪系)
Constant chord        G固定弦齒厚
Constant chord height        G固定弦齒高
Contact of tooth flanks        C齒面的接觸
Contact ratio and overlap ratio C重合度
Contrate gear D端面齒盤
Contrate gear pair Y圓柱齒輪端面齒盤副
Corresponding flanks        T通側齒面
Corrosive wear        M磨蝕磨損
Counterpart rack        C產形齒條
Crank element        Q曲拐元件
Crest,Top land        C齒頂面（齒頂）
Crest width        D端面齒頂厚
Crossed hilical gear pairs J交錯軸斜齒輪副
Crossing point of axes        Z軸線交點
Crowned teeth        G鼓形齒
Crown gear G冠輪
Crowning        G鼓形修整
Curtate cycloid D 短幅擺線
Curtate epicycloid        D短幅外擺線
Curtate hypocycloid        D短幅內擺線
Curtate involute        S縮短漸開線
Curtate ratio        D短幅系數
Curves and surface        Q曲線和曲面
Cutter interference        Q切齒干涉
Cycloid B擺線

如需查看更多請點擊下載齒輪相關詞匯